With the plan to ditch the top and side shelves in my original headboard design, I needed to come up with something to get rid of the TV tray I had been using as a nightstand. My first thought was to buy something, so I started surfing various online retailers. Nothing I came across would compliment my headboard. I decided to check out Etsy, which is full of unique products made by independent sellers. After just a few clicks I came across several sellers making floating nightstands, which instead of purchasing I decided to make. Doing so would allow me to use material that would match the headboard.
I still had some bead board, but not enough for an entire nightstand, let alone two. I could have used the oak boards I had, but everything in the master is pine. I didn’t want to mix wood. I could have purchased more reclaimed wood from Building Value, but then I’d need to join several pieces together for depth. Then I remembered I still had the original shelves from the 1st floor bathroom linen closet. They are 12″ x 24″, covered in paint and contact paper. I bet myself that underneath was a solid piece of old pine and I was right.
I took the four flattest boards to the Manufactory and ran them through their planer. I really need to invest in one as I spent more time driving to and from their facility than I did working on the four boards. I took the clean boards home, measured the space, and decided I would make 18″x11″x6″ nightstands. First step was ripping all the boards down to 11″ depth. Second step was ripping down to 18″ length and adding the miter angle. I cut the miter on one side of all boards, set my table saw to 18″. Unfortunately I didn’t place the first board correctly and cut the angle in the wrong direction. I was able to make the right cut, but now they are only 17.5″ wide. With the tops and bottoms cut I focused on the bead board. I glued four boards together and once dried ripped off the tongue and groove to reach 11″. I then used the same miter cut process I did for the top and bottom to create the four 6″ tall sides. I applied natural Danish oil to the outside of the of the bead board, painted the inside Indigo Batik, and applied dark walnut Danish oil to both sides of the pine.
The only piece left to address was the back. I have so much plywood that I decided to use 1/2″ plywood for the back. I painted the inside Indigo Batik, but applied the dark walnut Danish Oil to the back. Keep in mind I have no plans to follow, but my instincts told me to create a channel for the back panel to rest in. I had no room for error since I only had the four shelves for the top and bottom. I decided to make a prototype out of scrap plywood. I used my router to create the channel. My instinct was right. The prototype was very sound. The top and bottom of the back locked in place and I cut the width perfectly so there was no gaps on the sides.
Now it was just a matter of replicating the process on the actual wood. I ran the tops and bottoms through the router table, cut the backs to the appropriate sizes, and then prepared for the glue up. I remembered to use the “sizing” process I learned from the Woodworkers Guild of America YouTube video. The process went remarkably well. I used my pin nailer to help hold the pieces together until the glue dried. The next day I applied three coats of polyacrylic to the tops, since I know I’ll be setting glasses, mugs, or bottles on top and may not always have something underneath to protect the wood from stains.
The final step was attaching them to the wall and for that I used hanging cleats I ordered from Amazon. I had to trim a bit off due to my early miscut. Due to the width of the headboard I was not able to hit two studs, so I went to Northside Hardware and purchased six drywall anchors rated to hold 40lbs each. I love independent hardware stores as I was able to buy only the anchors (I was able to use the screws that came with the cleat) and the exact number I needed vs. a full pack. I decided to put three plus the stud screw for each nightstand.
With that a picture on Etsy turned into actual nightstands and the completion of a custom bedroom furniture set. Goodbye TV tray.
I’ve decided I’m going to make more of these stands out of all that oak wood I have. They were asking $150 on up for those on Etsy, so Sista Girl w/ Skills my have a shop on Etsy real soon!
Go girl! Looks great!